welcome

We are glad to welcome you to our website

Read article on ScienceDirect. Download PDF of articleDr. Review the editorial prior to submitting your manuscript; see article DOI to download the PDF. Access to Journals: Note: To read PDF files you will need the Adobe Acrobat reader, which can be downloaded free from the Adobe web site. Download PDF of article Dr. Smestad and Solar Energy Materials and Solar Cells" is available online. Solar energy materials and solar cellsVol. Fully low temperature interdigitated back-contacted c-Si(n) solar cells based on laser-doping from dielectric stacks Ortega, P.

Superior performance of V2O5 as hole selective contact over other transition metal oxides in silicon heterojunction solar cells Almora, Osbel; Gerling Sarabia, L. Transition metal oxides as hole-selective contacts in silicon heterojunctions solar cells Gerling Sarabia, L. Analysis of the Atomic Layer Deposited Al2O3 field-effect passivation in black silicon von Gastrow, G.

Monitoring degradation mechanisms in PTB7:PC71BM photovoltaic cells by means of impedance spectroscopy Arredondo, B.

Experimental determination of base resistance contribution for point-like contacted c-Si solar cells using impedance spectroscopy analysis Orpella, A.

Impact of Cu-Au type domains in high current density CuInS2 solar cells Moreau, A. Three-dimensional metallo-dielectric selective thermal emitters with high-temperature stability for thermophotovoltaic applications Garin, M. Optical interference for the matching of the external and internal quantum efficiencies in organic photovoltaic cells Betancur, R. Laser fired contacts applied to the rear surface of heterojunction silicon solar cells Martin, I.

Semi-transparent metal electrode of Cu-Ni as a replacement of an ITO in organic photovoltaic cells Ghosh, D. Recycling silicon solar cell waste in cement-based systems Fernandez-Carrasco, L.

Sputtered NiO as electron blocking layer in P3HT:PCBM solar cells fabricated in ambient air Betancur, R. Surface recombination analysis in silicon-heterojunction solar cells Barrio, R. Crystalline silicon surface passivation by amorphous silicon carbide films Vetter, M. Phosphorus-diffused silicon solar cell emitters with plasma enhanced chemical vapor deposited silicon carbide Orpella, A.

Optoelectronic devices based on evaporated pentacene films Voz, C. Preliminary study of a heat storage unit using a solid-solid transition Font, J. Shore D hardness, thermal expansion, dynamic mechanical analysis (DMA), Fourier transform infrared (FTIR) spectroscopy, compression and compression set (CS) measurements are made before and after the chemical exposure. The hardness, modulus at short times, degree of relaxation and CS increases while the coefficient of thermal expansion in HNBR tends to decrease with ageing time and temperature.

Temperature is shown to impose a greater effect on the properties than ageing time in the experiment. It sharply increases in the first stage of ageing and then decreases later with further exposure which suggests that chain scission dominates in the later stages of hydrocarbon ageing.

This effect is attributed to a dramatic change in the chemical structure of aged HNBR, i. These results are also qualitatively evaluated in the context of potential sealing applications of the material. The CFRP gears were milled from a composite plate and tested in mesh with a steel drive gear under five torque loads ranging between 0. A detailed gear damage analysis is conducted by employing scanning electron microscopy and high-resolution optical microscopy. Epoxy matrix microcracking is found to be the damage mechanism that leads to the final delamination failure.

CFRP gears exhibited a significantly improved performance and a longer fatigue lifespan in comparison with the polymer and polymer composite gears. The tensile and shear behaviors of the composites in swollen state were mainly studied via molecular dynamics simulations. The simulation results showed that the introduction of CNT and GN significantly improved the mechanical properties of the swollen NBR matrix. Higher elastic modulus, tensile strength and shear modulus of the composites were obtained by the incorporation of GN as reinforcement than that of CNT.

To explore the mechanisms on the above phenomenon, the atom displacements, interaction energy between the nano-reinforcements and rubber matrices, MSD of the cyclohexane and the free volume of the polymer composites were examined and interpreted accordingly.

A bench-scale test is presented as a practicable and efficient method to assess how different fire protective systems improve the structural integrity of CFRPs during fire.

The direct flame of a fully developed fire was applied to one side of the CFRP specimen, which was simultaneously loaded with compressive force. The uncoated specimen failed after just 17 s. Protection by these systems provides fire stability, as they multiply the time to failure by as much as up to 43 times.

Bench-scale fire stability testing is shown to be suitable tool to identify, compare and assess different approaches to fire protection. Herein, a hydrophobic thermoplastic lignin with favorable film formation properties was synthesized through simple crosslinking followed by esterification reactions. The chemical structure, glass transition temperature, and hydrophobicity were determined using Fourier transform infrared spectroscopy, 1H nuclear magnetic resonance spectroscopy, differential scanning calorimetry, and contact angle studies.